Zinco Guardrail Base GB-F (escape routes / escape paths) approx. 1.0 x 2.0 m, height approx. 43 mm
Superimposed / extra load supported construction base for penetration-free escape route / escape path solutions on flat roofs with railings on both sides up to 1.86 m apart. The required Superimposed / extra load is provided by the concrete slabs to be laid in the chippings bedding.
Construction base for penetration-free escape route / escape path boundaries made of profiled ABS-plastic with integrated aluminium profiles on the underside and a continuous, pre-drilled post support made of steel, hot-dip galvanized in accordance with DASt guideline 022, for mounting two opposing posts with integrated aluminium profiles on the underside, each with 4 M 10 screws spaced 100 x 75 mm apart, height of fixing flange above top of base plate approx. 35 mm, total height approx. 78 mm, backfill volume to top of Base plate approx. 16 l/sqm, dimensioned according to DIN 1991-1-1/NA for horizontal forces up to 1 kN/m, post spacing infinitely variable up to 1860 mm
| Order Nr.: | 3498 |
|---|---|
| Colour: | black / |
| Length [m]: | 2,0 |
| Material: | Base plate made of ABS-plastic with integrated aluminium profiles on the underside, Post support: galvanized steel |
| Width [m]: | 1,0 |
| Height [mm]: | 78.0 (total) |
| Packaging unit: | Piece |
| Weight [kg]: | 15.0 (total) |
| Pressure [kN/m²]: | 250.0 (with 10% yield) |
| Backfill volume [l/m²]: | 16,0 |
| Compatible with bitumen: | Yes |
| Additional information: | Post support: Length approx. 2000 mm, height approx. 35 mm from top of Base plate; post spacing infinitely variable up to 1860 mm. |
Construction base for non-penetrating escape route / escape path bordering made of profiled ABS plastic, length x width approx. 200 x 100 cm, height of Base plate approx. 43 mm, total height approx. 78 mm, with aluminium stiffening profiles on the underside and a continuous, pre-drilled steel post support on the top, hot-dip galvanized in accordance with DASt guideline 022, for mounting two opposing posts, each with 4 M 10 screws at a distance of 100 x 75 height, fixing flange above top of Base plate approx. 35 mm, dimensioned in accordance with DIN EN 1991-1-1/NA for horizontal forces up to 1 kN/m with a Superimposed / extra load of at least 200 kg/m², supply and tightly
Backfilling of the Base plate with gravel / grit (grain size max. 8/16 mm), requirement approx. 16 l/m².
With a concrete slab, the chippings bedding above the system base must be at least 5 cm so that the fixing flange is covered with approximately 1.5 cm of stone chippings.
Post spacing: infinitely variable up to 1860 mm
Make: Zinco Guardrail Base "GB-F"
Unit: pcs
Order Nr.: 3498
Scope of delivery:
Guardrail Base GB-corner "right", Order No. 3446
Guardrail Base GB-F, Order No. 3498
Installation steps Guardrail Base GB:
1. Laying out the Guardrail Base GB and installing the railings
.webp)
Measuring and laying out the Guardrail Base GB and ..
... assembly of the railings
Hole pattern of the fixing flange of the Guardrail Base GB
(4 slotted holes approximately / approx. 18 x 11)
Measure and lay out the Guardrail Base according to the planning documents. The specified spacing of the railing posts must be observed. If surface drainage is required and the post spacing is > 1.0 m, the gaps must be designed accordingly (e.g. Zinco Floradrain® FD 40).
The railings are installed using a screw connection with a suitable counter flange. Lanyards (M10 bolts, washers and stop nuts should be made of Stainless steel. The washer should be placed on the rubberised underside of the slotted hole. The material temperature should be above +5° during installation. The manufacturer's installation instructions must be observed when installing the railings!
2. Applying the required Superimposed / extra load
The required Superimposed / extra load in the adjacent table is for Guardrail Base GB depending on the required horizontal forces (h) and post spacing (s). If the wind load is greater than the required upright load, this must be used to determine the required Superimposed / extra load. Before applying the required Superimposed / extra load, we recommend checking all connections and the position of the railings.
Notice:
The Guardrail Base must always be filled with stone chippings or gravel / grit up to the top of the Base plate (approx. 43 mm). With a filling volume of 15-16 l/m², this corresponds to a Superimposed / extra load of approximately / approx. 25 kg/m². Superimposed / extra load can take the form of a concrete slab in a chippings bedding at least 50 mm high, with an appropriate greening structure, gravel or another equivalent bulk material.
superimposed / extra load required in kg/m²
Horizontal forces h (kN)
| 1,0 | 0,5 | 0,3 | |
| 1.00 s(m) | 200 | 100 | 60 |
| 1.25 s(m) | 250 | 125 | 75 |
| 1.50 s(m) | 150 | 90 |
This product is also available in other dimensions / measurements / specifications
Superimposed / extra load supported construction base for penetration-free escape route / escape path solutions on flat roofs with railings on both sides up to 1.86 m apart. The required Superimposed / extra load is provided by the concrete slabs to be laid in the chippings bedding.
Superimposed / extra load supported construction base for penetration-free escape route / escape path solutions on flat roofs with railings on both sides up to 1.86 m apart. The required Superimposed / extra load is provided by the concrete slabs to be laid in the chippings bedding.
Superimposed / extra load supported construction base for penetration-free escape route / escape path solutions on flat roofs with railings on both sides up to 1.86 m apart. The required Superimposed / extra load is provided by the concrete slabs to be laid in the chippings bedding.